
Misurazione senza fili né pile della temperatura e dell'umidità grazie al sensore EnOcean di NodOn
Questo modulo per uso interno è un sensore senza fili - senza pile, compatibile EnOcean. Associato ad una centrale domotica, permette di aumentare la temperatura di una stanza con una precisione di meno di 0.2°C e un campo di misura da 0°C a 40°C, così come l'umidità con un campo di misura da 0 a 100% RH.
Il sensore misura la temperatura ogni 100 secondi. Se la temperatura è variata più di 0.5°C in rapporto al valore precedente, la nuova temperatura è inviata alla centrale domotica. In assenza di variazione, la temperatura è inviata minimo ogni 15 minuti.
Una pila CR1216 può essere montata in opzione (non inclusa), portando l'autonomia del senosre a 3 anni nel buio completo.
Caratteristiche tecniche
- Alimentazione: Pannello solare
- Campo di misura della temperatura: da 0°C a 40°C (Risoluzione di temperatura 0.16°C) - Uso interno
- Campo di misura umidità: da 0 a 100% RH - Uso interno
- Montaggio a muro con biadesivo (incluso) o viti (non incluse)
- Pila CR1216 in opzione (non inclusa) per uso in zona buia (Autonomia 3 anni buio completo)
- Temperatura di esercizio: da 0°C a 40°C - Altitudine massima: 2000m
- Protocollo Radio EnOcean®: 868.3MHz – EEP: A5-02-05
- Portata: 30m all'interno
- Dimensione: 80x26x18mm
- Garanzia 2 anni
Norme
- EN 301489-3: Vl.4.1; EN 61000-6-1: 2007
- EN 300220-1: V2.4.1, EN 300220-2: V2.4.1
- EN60950-1: 2006+All:2009
- EN62479: 2010
- Uso generale
- Misurazione temperature/umidità/Co2…
- Tipo
- Collettore
- Funzione
- Temperatura
Umidità - Compatibilità domotica
- eedomus+ - compatibilità attraverso passerella opzionale
- Protocollo
- Enocean
Produits de marque NodOn
Accessori

I clienti che hanno acquistato questo prodotto hanno comprato anche:

Sehr gutes Produkt
Der Sensor hat werte die mit anderen Messgeräten übereinstimmen.
Funktioniert auch ohne direkter Sonneneinstrahlung seit Wochen.
Die Sendeleistung reicht vom ersten Stock bis in den Keller ohne Probleme.
Very precise
Very precise measurements. Does not need much light to work. I have 8 sensors installed and only one sensor needs a battery. It's installed in a room without any window.
Climat de bureau agréable
Le capteur est connecté au logiciel Jeedom, qui fonctionne sur un Rasberry-Pi. L'installation a été facile et le capteur fonctionne parfaitement.
Capteur Temps
Bon produit après un étalonnage de la température cela fonctionne très bien.
Works fine with my gateway
This one works fine with my homee (http://hom.ee) gateway.
Easy opening of the sensor (which unfortunately is not documented on the included small manual- simply push the back-cover either left or right (holding the sensor horizontally) and you will be able to then turn the back-cover off with ease) and easy one-press inclusion.
The sensors regularly (every 10 minutes) reports temperature and humidity as accurately as my existing Everspring/Devolo Z-Wave sensors that unfortunately need battery replacement every 6-9 months.
This one is small and nearly invisible and has good signal strength (the ground floor and parts of the first floor of my house are fully covered, w/o the need for additional signal relay via plugs so far) and I will therefore use these sensors in my wet rooms and gradually replace my existing Z-Wave sensors with this product.
Main motivation factor: No more need to regular replace expensive CR123 batteries, as this works fine with small solar panels (tested it w/o CR1216 batteries so far) and less intrusive (especially less intrusive than the Everspring ST814, that has one advantage though: It shows the current values on its embedded display, which the NodOn only does via the Gateway). Will still need to test (probably with CR1216 batteries) in my basement that does not have as much light.