Z-Wave+ module consumption monitor in Din Rail format
This Z-Wave Plus module is used to measure the power consumption of a Single phase system of up to 65A. Its DIN Rail format enables installation directly into an electrical cabinet. The smart meter uses fast sampling of voltage and current signals to measure power consumption. The integrated microprocessor measures energy, current and power factor.
It transmits consumption to your controller via Z-Wave protocol but also has an LED display on the front of the case enabling you to connect an optical pulse sensor for a variety of additional uses (1 pulse = 1Wh).
With a wired switch output and an infra-red output, the Smart Meter can control additional DIN Rail switches. This enables you to have loads switched directly from the electrical board and controlled via Z-Wave. Particularly convenient for load shedding, to disable an entire sub-circuit in your electrical system, etc.
Connection of optional relays:
- Bistable 32A 4 pole switch, with infra-red control: ISK_BICOM432-40
- 2-pole 32A actuator, wired control: ISK_IKA232-20
Thanks to Z-Wave PLUS technology the module has improved range and faster communication. It remains, of course, compatible with previous Z-Wave versions.
This module also acts as a radio repeater maximizing the range of your Z-Wave installation.
Features
- Analyses the overall power consumption of a phase.
- Installs directly in the electrical cabinet
- Integrated 500 series Z-Wave chip (Z-Wave+)
- Communication 250% faster compared to standard Z-Wave devices
- Consumption of less than 2W
- Operating temperature of -10 to 40˚C
- IR connector for an additional DIN relay
- Wired connector for an additional DIN relay
- LED pulse for an optional optical counter
- Measurement and transmission of the following data:
- Voltage:
- Current intensity (I)
- Active power (in W)
- Total power consumption (in kWh)
- Reactive power (in var)
- Total reactive power (kVarh)
- Total apparent power (in kVAh)
- Power factor (PF)
TECHNICAL SPECIFICATIONS
- Main terminals (LI, NI, Lo, No)
- Contacts capacity: 1.5 ... 16 (25) mm2
- Connection screws: M5
- Max torque: 3.5 Nm (PZ2)
- Optional terminals (1,2,4,5)
- Contact capacity: 0.05 ... 1 (2.5) mm2
- Screws: M3
- Max torque: 0.6 Nm
- Measuring input:
- Type (connection): single phase (1b)
- Reference current (Iref): 5 A
- Maximum current (Imax): 65 A
- Minimum current (Imin): 0.25 A
- Starting current: 20 mA
- Voltage (Un): 230 V (±20 %)
- Power consumption at Un: < 2W
- Nominal frequency (fn): 50 and 60 Hz
- Accuracy:
- Active energy and power:
- Standard EN 62053-21: class 1
- Standard EN 50470-3: class B
- Reactive energy:
- Standard EN 62053-23: class 2
- Optical communication:
- Type: IR - used to control BICOM432-40-IR
- Input (1):
- Rated voltage: 230 V (± 20%)
- Input resistance: 450 kOhm
- Safety:
- Indoor meter: yes
- Degree of pollution: 2
- Protection class: II
- AC voltage test: 4 kV
- Installation Category: 300 Vrms cat. III
- Standard: EN 50470
- Ambient conditions and EMC:
- According standards for indoor active energy meters.
- Temperature and climatic condition according to EN 62052-11
- Ambient conditions and Safety:
- According standards for indoor active energy meters.
- Temperature and climatic condition according to EN 62052-11
- Dust/water protection: IP20
- Operating temperature: -10 ... 40°C
- Storage temperature: -40 ... 70°C
- Enclosure material: self extinguish
- complying UL94 V
- Indoor meter: yes
- Degree of pollution: 2
- AC voltage test: 4 kV
- Standard: EN 50470
- Distance: up to 30 m indoors (depending on building materials)
- Weight (with packaging): 150g (170g)
- Frequency range: 868.4 MHz, Z-Wave
- Installation Din rail 35mm
- Dimensions (W x H x D): 36 x 90 x 64mm
- Package dimensions
- (W x H x D): 40 x 95 x 80mm
- Colour RAL 7035
- EC Directives conformity:
- EC Directive on Meas. Instruments 2004/22/EC
- EC Directive on EMC 2004/108/EC
- EC Directive on Low Voltage 2006/95/EC
- EC Directive WEEE 2002/96/EC
