The new EUROtronic Thermostat has a brand new design. You can change the panels (available as accessories) and personalise the thermostat according to your preferences.
The device is equipped with FLiRS (Frequently Listening Receiver Slave) and reacts immediately to orders from the Z-Wave controller. In addition, the device may be connected to an external Z-Wave temperature sensor. In this way, the thermostat refers to the temperature of the external sensor, which may be positioned in the middle of the room.
The thermostat display is backlit and has a large LCD screen. What's more, you can lock the buttons on it using the integrated child protection.
The multicoloured LED of the central button allow for intuitive use, as the user is encouraged to following the instructions based on the flashing LED on the central button.
The Spirit Z-Wave Plus thermostat head comes with silver accessories for the battery compartment and the decorative ring. A neutral white battery compartment is included.
The valve may be used as a heating thermostat or as an actuator, based on the configuration of the device. The temperature measured or the position of the actuator of the thermostat are sent to the compatible Z-Wave controller.
Functions
- Replaces the thermostatic head of your radiator
- Control your radiator remotely
- Save up to 30% in heating costs
- "Open window" detection
- Child protection
- 3 adapters (RA Danfoss, Danfoss RAV, Danfoss RAVL) included
- Various battery compartment and decorative ring colours available separately
Technical characteristics
- Power source: 2 x 1.5V LR6/AA
- Emission frequency: 868.42MHz
- Range: up to 30m indoors and 100m outdoors
- Connection: M30 X 1.5 mm
- Temperature measurement frequency: Every minute
- Recommended temperature range: 6 to 28°c
- Operating temperature: 0 to 50 ° C
- Protection category: IP20
- Dimensions (L x H x D): 56 x 68 x 89 mm
- Weight: 176g (batteries included)
- Use
- Heating Management
Temperature/Humidity/CO2 Monitoring - Type
- Module
Thermostatic heads - Function
- Actuator
Heating
Temperature - Gateway compatibility
- Fibaro Home Center - total compatibility
Homey - total compatibility
eedomus+ - total compatibility - Protocol
- Z-Wave Serie 500
Accessories
Customers who bought this product also bought:
FIBARO - Z-Wave Universal Binary Sensor FGBS-222 (FIBARO Smart Implant)
Philio - Z-Wave+ Outdoor Motionsensor with magnetic holder and lens cover PSP05-D
Pas terrible
Ces têtes sont pleines de défaut, c'est pourquoi j'en ai commandé d'autres, des Danfoss en Zigbee. Les principaux problems sont
1) les piles s'usent très vite
2) elles sont très bruyantes
3) peu fiables, souvent la commande ne passait pas avec ma box Jeedom.
Fonctionne parfaitement, comme attendu
Installation et inclusion sous Jeedom sans aucun soucis.
Permet de contrôler à distance un radiateur (avec en prime un relevé de température). Fonctionne parfaitement et répond complètement à mes attentes.
Attention toute fois:
Il existe de nombreux standards au niveau di filetage pour l'installation, il est livré avec plusieurs adaptateurs mais bien faire attention et se renseigner avant la commande/l'installation.
Malgré mes efforts, je n'ai pas trouvé de récapitulatif sur les normes pour la fixation des têtes thermostatiques (nom de la norme avec un schéma et les dimensions). Si quelqu'un a cette info, un reply serait grandement apprécié.
Réponds pleinement à mes attentes
J'en ai installé sur tous mes radiateurs à la maison pour gérer la température par pièce et faire des économies.
Fonctionne parfaitement avec ma centrale domotique maison basée sur raspberry pi 4, un stick Z-Wave Aeotec Gen 5 et HomeAssistant.
Rapport qualité-prix intéressant.
Les conseils de l'équipe sont toujours au top.
Reliable and accurate
I'm using on underfloor heating and these are good at keeping the right temperature.
A bit noisy, and can be fiddly to get the right spacing for the needle valve, but good once set up.
Pourrait mieux, mais bien
La configuration est un peu compliquée, il faut réveiller la vanne via la molette pour prendre en compte les paramètres, comme le délai avant réveil, mais après, c'est vraiment sympa.
Sur domoticz, j'ai des plages horaires pour contrôler la vanne ou par exemple très chaud quand la lampe de chevet est allumée et plus froid éteinte... J'aime bien qu'il fasse chaud pendant que je bouquine, mais frais pendant que je dors.
Donc dans les points forts :
- marche très bien avec domoticz
- vraiment mieux que les robinets "à régulation" danfoss
- dure longtemps sur piles alcalines
Et les points faibles :
- l'installation qui nécessite un tournevis
- la configuration initiale nécessitant de réveiller la vanne
- la tête est assez grosse
- impossible à employer sans installation z-wave