All reviews
Je l'utilise avec Home Assistant Yellow, le Zigbee y est intégré.
L'appareil est reconnu tout de suite, et on peut tout gérer, tension, consommation, consommation cumulée, télécommande, température de la pièce (idéal pour commander un chauffage d'appoint). Grâce au protocole Zigbee, plus besoin de wifi pour les objets connectés.
En plus, livraison très rapide, je remercie swiss-domotique pour ça.
Installation par autocollant, adhésion pas terrible du capteur sur certaines surface (métalliques en l'occurence...). Probablement à réserver pour une installation sur un cadre de fenêtre/porte en bois pour le capteur, que l'on peut fixer avec des vis. Par contre l'aimant tient facilement sur du métal (partie magnétique !), mais je saurai dire si l'adhésif est suffisant pour d'autre surface.
La mise en route et l'inclusion sont simples et faciles à réaliser, du moins sur eedomus. Le temps de réponse est sufisamment rapide pour mon besoin (détection état ouvert-fermé d'une porte de garage). La petite taille et le design sont également appréciables.
Adaptateur qui transforme une prise européenne au format suisse. Utilisé pour mettre un répéteur Aeotec au format d'une prise suisse pour étendre un réseau z-wave. Utilisation simple et rapide. Attention, si on veut retrouver le format de prise initial, retirer l'adaptateur peut s'avérer diffile, mais avec un peu de patience, on y arrive quand même !
Bonjour,
Merci pour votre retour. Effectivement, comme indiqué sur la fiche produit, il s'agit d'un adaptateur non détachable. C'est une obligation légale. Les adaptateurs détachables sont autorisés uniquement à très cours terme, en tant qu'adaptateur de voyage.
J'avais besoin d'étendre mon réseau z-wave à un garage sous-terrain pour commander l'ouverture d'une porte de garage + état d'ouverture. Pas de réseau avec la "maillage" habituel, probablement à cause de la ferraille +++ dans le béton armé. En faisant un relais de 2 répéteurs z-wave dans le couloir qui mène au garage, ça marche tip-top !!!
Installation facile sur la box eedomus.
The Z-TRM6 is the evolution of the Z-TRM3, which I also own. The new design is made to last with a metal frame and new terminals. The attachment of the facade has also been improved for the better.
I don't quite like that the power and load terminal are interdigitated (L-L-N-N) and not grouped (L-N-L-N) which would make connection easier with short cables, but that's a detail. More important is that if, like me, the wall box is a Swiss-standard, you'll have to use the corner holes in the frame to fix the thermostat on the wall. Plan for tiny countersunk screw of 3mm otherwise you won't be able to affix the front panel. They could have made more room in the plastic frame for that.
Adding the thermostat to my Fibaro HC3 gateway went well (in unsecured mode because the HC3 usually fails adding devices in secure mode!!). I ended up with 4 devices: 1 thermostat and 3 multilevel sensor devices with each a temperature. That's where things became tricky. I was expecting to see one fo the temperatures in each of the multilevel sensor (internal ambient, external ambient and floor) but all the values stay at zero, no matter what. Furthermore the documentation show "max. nodes = 0 for those 3 group, so I don't quite see the interest. Only the thermostat temperature has a value! What I discovered is that the temperature displayed there is the temperature of the sensor you use according to the selected regulation mode (A, AF, etc.). Power and Energy are reported as expected and the 4 operation modes are also supported. There is also a switch status device which stays to "off" no matter the real thermostat state. So all-in-all I ended up hiding all the elements except the thermostat control and temperature, which is sufficient for me. I wonder if it is an HC3 or Z-TRM6 issue.
Overall price-to-value is not as good as I would expect from reading the documentation, but it is acceptable.
Rasche Lieferung, tiptop