All reviews
Le gadget qui me manquait pour que me maison soit encore plus inteligente. Les rideaux s’ouvrent et se ferment au levé et au couché du soleil, sans que j’y pense. Génial, non?
Connecté avec Home Assistant
Un peu grand et lourd mais le moteur reste caché derrière les rideaux.
5 étoiles ????
Vraiment la référence en ampoule Wi-Fi !
Elle a remplacé une ampoule Wiz qui perdait constamment la connexion Wi-Fi (pourtant placée à 1 mètre du point d'accès). Avec cette ampoule Shelly, c'est fiable et les divers réglages via l'application ou l'interface web permettent de connecter l'ampoule directement à une installation domotique (Home Assistant dans mon cas), tout en s'affranchissant totalement des fonctions cloud, tout cela dans une parfaite stabilité.
Je recommande sans réserve !
Peut fonctionner sans HUB Aqara : je l'ai connecté directement à un contrôleur SkyConnect sous Home Assistant : la valeur de température est correctement remontée (il faut appliquer un petit offset, car la valeur est un peu surestimée par rapport à la température réelle). La valeur de batterie semble totalement fantaisiste, mais ce n'est pas si grave, vu que le capteur a l'air d'être assez endurant.
J'ai acheté cette tête thermostatique en pensant que c'était le même modèle "rebrandé" que la tête EUROTRONICS, le hardware semblant identique. Malheureusement, ce dernier n'est pas reconnu comme EUROTRONICS dans mon installation Jeedom, et même pas reconnu du tout.
Une lecture de certains forums sur Internet montre que cette tête n'est pas toujours nativement supportée par certains systèmes domotiques, donc il faut vraiment vérifier la liste de compatibilité avant de l'acquérir.
La bonne nouvelle, c'est que même si elle n'est pas intégralement reconnue dans Jeedom, certaines commandes principales, comme ON,OFF ou mode ECO, sont accessibles et fonctionnent, ce qui était le plus important dans mon cas (pouvoir activer ou désactiver le chauffage à distance). L'accès Z-Wave aux consignes, par contre, ne fonctionne pas, malgré toutes mes tentatives de configuration manuelle.
Included with S2 security in Home Assistant via my Z-Wave-js ui app with an Aeotec - Z-Wave+ Z-Stick ZW090C+ USB Controller (on a PI4). I prefer this model over the FGS-223 because it has the S2 security, even if you need to put the "jumper" for a classic 230V setup (from L to IN pin), but security come first!
I used this product as thermostat for floor electrical heating. The integration with Fibaro HC3 is OK-ish (no parameters template), but so far the thermostat keeps going back to Off mode, without any apparent reason.
I also see the temperature measurement is very noising and swings by several degrees on a 35K NTC. I will probably return it if I can't find a solution.
I also use the Heatit ZM and I don't have any issue, but unfortunately it works only with 10K NTC.
The Z-TRM6 is the evolution of the Z-TRM3, which I also own. The new design is made to last with a metal frame and new terminals. The attachment of the facade has also been improved for the better.
I don't quite like that the power and load terminal are interdigitated (L-L-N-N) and not grouped (L-N-L-N) which would make connection easier with short cables, but that's a detail. More important is that if, like me, the wall box is a Swiss-standard, you'll have to use the corner holes in the frame to fix the thermostat on the wall. Plan for tiny countersunk screw of 3mm otherwise you won't be able to affix the front panel. They could have made more room in the plastic frame for that.
Adding the thermostat to my Fibaro HC3 gateway went well (in unsecured mode because the HC3 usually fails adding devices in secure mode!!). I ended up with 4 devices: 1 thermostat and 3 multilevel sensor devices with each a temperature. That's where things became tricky. I was expecting to see one fo the temperatures in each of the multilevel sensor (internal ambient, external ambient and floor) but all the values stay at zero, no matter what. Furthermore the documentation show "max. nodes = 0 for those 3 group, so I don't quite see the interest. Only the thermostat temperature has a value! What I discovered is that the temperature displayed there is the temperature of the sensor you use according to the selected regulation mode (A, AF, etc.). Power and Energy are reported as expected and the 4 operation modes are also supported. There is also a switch status device which stays to "off" no matter the real thermostat state. So all-in-all I ended up hiding all the elements except the thermostat control and temperature, which is sufficient for me. I wonder if it is an HC3 or Z-TRM6 issue.
Overall price-to-value is not as good as I would expect from reading the documentation, but it is acceptable.